FPSADMIN.ECT_STATE_7D_2D_CW

FACILITY

VARCHAR2(6)

N

Facility is included in almost every join in the DWH so this represents a definitive split. A route must have all steps on tools in the same facility. A tool must process all lots in the same facility. If your site has multiple buildings where lots run on routes using tools in multiple buildings then everything should be one facility. For example, multiple Fab buildings. But if your site has independent facilities like Fab and Test and Assembly where lot may progress from one to the next but on different routes then these should be different facilities. Since this column is in virtually every table it is critical that the value here is exactly matches what is in the MES if the MES has facility. Use facility_display for the display friendly name displayed in applications. See site_name comment for client/site/facility example. (* from FPSINPUT.GEN_FACILITIES)

ROUTE

VARCHAR2(256)

N

Route that has threading requirements (* from FPSINPUT.RTG_STEP_THREADING)

STEP

VARCHAR2(256)

N

A single processing step within a route representing a single tool visit. Step is often a very complex string and should rarely be displayed. Instead we should use process_display. (* from FPSINPUT.RTG_ROUTE_STEPS)

BANK

VARCHAR2(36)

N

Lots which are not on a route are considered in a bank and the bank name indicates why the lot is off route. Bank must be NA for lots which are on a route. Our standard filter for active lots is bank = NA. (* from FPSINPUT.RTG_BANKS)

PRD

VARCHAR2(64)

N

Prd determines the route which is used to process the lot in the facility and what tools, recipes, durables, etc. can be used at each step. Prd also determines the next facility for the lot when it finishes its route. For detailed information on prd vs. planprd see table comments in RTG_PLANPRDS. (* from FPSINPUT.RTG_PRDS)

PLANPRD

VARCHAR2(64)

N

Planning product used for all planning purposes. All lots with the same planprd are interchangeable to ship to the customer regardless of their prd, route, technology, wafer size, etc. For detailed information on prd vs. planprd see table comments in RTG_PLANPRDS. (* from FPSINPUT.RTG_PLANPRDS)

PRTY_CTM_GROUP

VARCHAR2(7)

N

This is one of the primary keys of our CTM tables. We use this group rather than the priority because we often have several different priorities which are close and are expected to have the same cycle time. (* from FPSINPUT.WIP_PRIORITIES)

LOT_GROUP

VARCHAR2(8)

N

Lot_group is a grouping of lot_family and is the highest grouping in the lot type hierarchy. There should be only a few values for lot_group, i.e. Prod, Dev, TW. We group WIP and moves by lot_group on the dashboard and we group cycle time calculations by lot_group so this is an important field. (* from FPSINPUT.WIP_LOT_GROUPS)

IS_NONSTD

CHAR(1)

N

Our column to indicate non-standard processing at the step. For example, an experiment or a chain that is only active at a particular step or set of steps and then goes back to being normal for the route. If an experiment is severe enough that it affects the final product and has to be planned separately then it will be its own prd or planprd. (* from FPSBASE.WIP_LOT_HIST)

ECT_STATE

VARCHAR2(42)

N

ECT state is the lowest level state of our Enhanced Cycle Time hierarchy and the value which is stored in WIP_LOTS_REALTIME and ECT_HIST. We can lookup all information about the ECT state including process state in ECT_STATE_DIAGRAM. (* from FPSADMIN.WIP_ECT_STATES)

CTM_DATA_INST

DATE

NUM_LOTS_ENDWIP

NUMBER(6)

NUM_LOTS_STARTWIP_2D

NUMBER(6)

NUM_LOTS_STARTWIP_7D

NUMBER(6)

NUM_LOTS_STARTWIP_CURRWK

NUMBER(6)

QTY_ENDWIP

NUMBER(12)

QTY_STARTWIP_2D

NUMBER(12)

QTY_STARTWIP_7D

NUMBER(12)

QTY_STARTWIP_CURRWK

NUMBER(12)

START_2D

DATE

START_7D

DATE

START_CURR_WEEK

DATE

TOTAL_UNIT_SECONDS_2D

NUMBER(24)

TOTAL_UNIT_SECONDS_7D

NUMBER(24)